High-accuracy 2D Laser Displacement SensorLJ-G series

LJ-G5001P

Controller, PNP Type, English Manual

SPECIFICATIONS

Select Language

Model

LJ-G5001P

Head compatibility

Compatible

Number of connectable sensors

2 units max.

Display

Minimum display unit

0.1 µm *1, 0.001 mm2, 0.01° (Inch mode : 0.01 Mil, 0.00001 inch)

Maximum display range

±99999.9 mm, ±999999 mm2, ±99999.9° (Inch mode : ±9999.99 Mil, ±999.999 inch)

Input terminal block

Laser remote interlock input

Non-voltage input

Trigger input

For sensor head A, voltage input

Timing 1 input

Voltage input

Auto-zero 1 input

Reset input

Output terminal block

Analog voltage output

±10 V x 2 outputs, output impedance: 100 Ω

Total judgment output

PNP open-collector output

Error output

PNP open-collector output (N.C.)

Process output

PNP open-collector output

Trigger input enable output

For sensor head A, PNP open-collector output

Adjusted error output

Expansion connector

Timing 2 input

Voltage input

Auto-zero 2 input

Trigger input

For sensor head B, voltage input

Program switching input

Voltage input, 4 inputs

Memory card save input

Voltage input

Laser-Off input

For sensor head A/B, voltage input

Judgment/Binary output

3-level judgment output: OUT1 to OUT8, total judgment output
Binary output: OUT1 to OUT8 measured data output (21 bits)
PNP open-collector output*2

Strobe output

PNP open-collector output

Trigger input enable output

For sensor head B, PNP open-collector output

Adjusted error output

Analog RGB monitor output

SVGA (800 x 600 pixels)

RS-232C interface

Measured data output and control input/output (Maximum baud rate: 115200 bps, selectable)

USB interface

In conformity with USB Revision 2.0 HI-SPEED (USB 1.1 Full-SPEED compatible)

Ethernet interface

100BASE-TX/10BASE-T

Memory card

Compatible with NR-M32 (32 MB), GR-M256 (256MB), and NR-M1G (1GB). (with FAT32)

Major functions

Sensor heads calculation, Profile adjustment, Filter, Smoothing, Averaging,
Position adjustment, OUT name change, Measurement mode selection
(Height, position, gap, width, center position, section area, intersection, angle, profile comparison, profile tracking),
Scaling, Average, Measurement, Measured value alarm, Tolerance setting, Auto-zero, Storage (data/profile),
Memory card saving, Program memory, Trigger mode change, Mutual interference prevention, Measuring range change,
Calibration, Laser light adjustment, Sampling time setting, Mask, Profile alarm setting, Inclination adjustment, Height adjustment,
Display language switch, Setting support software connection, Trigger pitch/Measuring time display, etc.

Rating

Power voltage

24 VDC ±10%, Ripple: 10% (P to P) or less

Maximum current consumption

800 mA or less with 1 sensor head/1 A or less with two sensor heads

Environmental resistance

Operating temperature range

0 to 50°C 32 to 122°F

Operating ambient humidity

35 to 85% RH (No condensation)

Weight

Approx 1050 g

*1 When LJ-G015 or LJ-G015K is connected only. When other sensor heads are connected, the minimum display unit is 1 µm.
*2 Time-sharing output of judgment results or binary measured data.
The rating of the NPN open-collector output: 50 mA max. (30 V max.), residual voltage of 1 V max. The rating of the PNP open-collector output: 50 mA max. (30 V max.), residual voltage of 1 V max.
The rating of the non-voltage input: 1 V or less ON voltage, 0.6 mA or less OFF current (Trigger input terminal: 1 V or less ON voltage, 1.0 mA or less OFF current)
The rating of the voltage input: 26.4 V maximum rating, 10.8 V or less ON voltage, 0.6 mA or less OFF current (Trigger input terminal: 26.4 V maximum rating, 10.8 V or less ON voltage, 1.0 mA or less
OFF current)

Measurement Library

Latest / Most Downloaded

    • General Catalog Request
    • Trade Shows and Exhibitions
    • eNews Subscribe

    Measurement Sensors