Recent Searches
    Series ( results)
      Models ( results)
        Keywords
          1. Home
          2. Products
          3. Measurement Sensors
          4. Laser Displacement Sensors(1D)
          5. Surface Scanning Laser Confocal Displacement Meter
          6. Models
          7. Controller, Not Subject to Export Control, with Camera Function

          Surface Scanning Laser Confocal Displacement MeterLT-9000 series

          Controller, Not Subject to Export Control, with Camera Function

          LT-9501H

          SPECIFICATIONS

          Select Language

          Model

          LT-9501H

          Measuring unit compatibility

          Measuring units are interchangeable without factory recalibration.

          Display

          Minimumdisplayable unit

          0.1 µm *1, 1 µm2, 0.01°

          Display range

          ±9999.99 µm, ±999999 µm2, 9999.99°

          Microscopefunction

          Available

          Display cycle

          10 times/sec.*2

          Terminal block

          Analog output

          ±10 V x 2 outputs, output impedance: 100 Ω

          Timing input

          Non-voltage input

          Reset input

          Auto-zero input

          Monitor dedicated power supply

          24 VDC*3

          Control I/O

          Judgment mode

          3-step limits output

          For OUT1 and OUT2, and NPN open collector output*4

          Binary mode

          Binary output

          Measured data output (21 bits), OUT1/OUT2/PROFILE selectable
          NPN open collector output*4

          Strobe output

          NPN open collector output*4

          Binary selector output

          Binary selection input

          Non-voltage input*4

          Stability output

          NPN open collector output

          Laser remote input

          Non-voltage input

          Program switching input

          Non-voltage input x 3 inputs

          RS-232C interface

          Measured data output and control I/O (Selectable up to baud rate 115200 bps.)

          Video output

          NTSC compliant (PIN connector)

          Main functions

          Displacement mode

          Distance measurement, Transparent object thicknessmeasurement, Angle measurement, Relative anglemeasurement, Surface selection, Dark-out, Mask, Trend graphdisplay, and Scan width/interval change*5

          Profile mode

          Area selection (Average, Maximum, Minimum, Maximum-tominimum,
          Area) Area calculation, Scan width/interval change,
          Dark-out, Smoothing, Averaging, and Profile data output*6

          Common

          Light intensity accumulation, Microscope (LT-9501H, LT-9501HSO (5654) only), Tolerance
          judgment, 8-program registration, Calibration, Averaging, Hold modes, Auto-zero, and
          interface language selection

          Rating

          Power voltage

          100 to 240 VAC ±10 %, 50/60 Hz

          Power consumption

          110VA or less

          Environmental resistance

          Pollution degree

          2

          Overvoltage category

          II

          Ambient temperature

          0 to +35 °C 32 to 95 °F

          Relative humidity

          35 to 85 % RH (No condensation)

          Weight

          Approx. 2.4 kg

          *1 Display changes every ±0.3 µm.
          *2 Varies depending on the setting
          *3 Dedicated power supply for the monitor specified by KEYENCE.
          *4 Select either the Limits mode or the Binary mode.
          *5 Select either the Distance mode or the Profile mode. (Distance mode is only available with the LT-9501HSO (5654)and LT-9001HSO (5655).)The rating of the NPN open-collector output is 30 mA (30 V or lower) maximum, and residual voltage is 0.5 V.The rating of the Non-voltage input is ON voltage 1 V or lower, and OFF current 0.6 mA or lower.
          *6 Select either the Distance mode or the Profile mode. (Distance mode is only available with the LT-9501HSO (5654)
          and LT-9001HSO (5655).)
          The rating of the NPN open-collector output is 30 mA (30 V or lower) maximum, and residual voltage is 0.5 V.
          The rating of the Non-voltage input is ON voltage 1 V or lower, and OFF current 0.6 mA or lower.

          Tips of Measurement

          • General Catalog Request
          • Trade Shows and Exhibitions
          • eNews Subscribe

          Measurement Sensors