Specs : Manual-Calibration Fiberoptic Sensor

Model		FS-T1	FS-T2	FS-M1	FS-M2
Image
Type		Main unit	1-line expansion unit	Main unit	1-line expansion unit
Output		NPN
Light source		Red LED
Sensitivity adjustment/Mode selection		Button		8-turn trimmer (with indicator), FINE/TURBO (switch-selectable)
Response time		250 µs		250 µs (FINE) /500 µs (TURBO)
Operation mode		LIGHT-ON/DARK-ON (switch-selectable)
Indicator lamp		Output indicator: Red LED, Stable operation indicator: Green LED Calibration indicator: Orange LED		Output: Red LED Stable operation: Green LED
Timer function		ON-delay: 40 ms/OFF-delay: 40 ms/Timer OFF (switch-selectable)
Input		Non-voltage input (contact, solid state)		―
Control output		NPN open-collector 100 mA max. (24 VDC max.), Residual voltage: 1 V max.
Stability output		NPN open-collector 50 mA max. (40 VDC max.), Residual voltage: 1 V max. ^*1
Protection circuit		Reversed polarity protection, over-current protection, surge absorber
Unit expansion		Up to 16 expansion units can be connected (a total of 17 units).^*2
Mutual interference suppression		4		FINE : 4, TURBO/SUPER: 8
Rating	Power voltage	12 to 24 VDC ±10 %, Ripple (P-P) 10 % or less	12 to 24 VDC ±10 %, Ripple (P-P) 10 % or less^*4	12 to 24 VDC ±10 %, Ripple (P-P) 10 % or less	12 to 24 VDC ±10 %, Ripple (P-P) 10 % or less^*4
	Current consumption	35 mA or less
Environmental resistance	Ambient light	Incandescent lamp: 10,000 lux max., Sunlight: 20,000 lux max.
	Ambient temperature	-10 to +55 °C 14 to 131 °F (No freezing)^*3
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
	Shock resistance	500 m/s², 3 times in each of the X, Y, and Z directions
Case material		Polycarbonate
Weight		Approx. 75 g	Approx. 40 g	Approx. 75 g	Approx. 40 g
^1 Only the FS-T1 and FS-M1 can provide stability outputs. ^2 If more than one unit is used together, the ambient temperature varies with the conditions below. Mount the units on the DIN rail with mounting brackets and check that the output current is 20 mA or less. 3 to 10 Units: -10 to 50°C 14 to 122°F, 11 to 16 Units: -10 to 45°C 14 to 113°F ^3 When several units are connected, the ambient temperature requirement varies depending on the total number of units connected. When 3 to 10 units: -10 to +50 °C 14 to 122 °F When 11 to 16 units: -10 to +45 °C 14 to 113 °F When connecting several units, be sure to mount the units to a metallic DIN rail. Make sure that the output current does not exceed 20 mA. ^4 Power to the FS-T2/M2 is supplied through the FS-T1/M1/V1/V11/, PS-T1, LV-21A/11A.

Back to top

Model		FS-T1P	FS-T2P	FS-M1P	FS-M2P
Image
Type		Main unit	1-line expansion unit	Main unit	1-line expansion unit
Output		PNP
Light source		Red LED
Sensitivity adjustment/Mode selection		Button		8-turn trimmer (with indicator), FINE/TURBO (switch-selectable)
Response time		250 µs		250 µs (FINE) /500 µs (TURBO)
Operation mode		LIGHT-ON/DARK-ON (switch-selectable)
Indicator lamp		Output indicator: Red LED, Stable operation indicator: Green LED Calibration indicator: Orange LED		Output: Red LED Stable operation: Green LED
Timer function		ON-delay: 40 ms/OFF-delay: 40 ms/Timer OFF (switch-selectable)
Input		Non-voltage input (contact, solid state)		―
Control output		PNP open-collector 100 mA max. (40 VDC max.), Residual voltage: 1 V max.
Stability output		PNP open-collector 50 mA max. (40 VDC max.), Residual voltage: 1 V max.^*1
Protection circuit		Reversed polarity protection, over-current protection, surge absorber
Unit expansion		Up to 16 expansion units can be connected (a total of 17 units).^*2
Mutual interference suppression		4		FINE : 4, TURBO/SUPER: 8
Rating	Power voltage	12 to 24 VDC ±10 %, Ripple (P-P) 10 % or less	12 to 24 VDC ±10 %, Ripple (P-P) 10 % or less^*4	12 to 24 VDC ±10 %, Ripple (P-P) 10 % or less	12 to 24 VDC ±10 %, Ripple (P-P) 10 % or less^*4
	Current consumption	35 mA or less
Environmental resistance	Ambient light	Incandescent lamp: 10,000 lux max., Sunlight: 20,000 lux max.
	Ambient temperature	-10 to +55 °C 14 to 131 °F (No freezing)^*3
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
	Shock resistance	500 m/s², 3 times in each of the X, Y, and Z directions
Case material		Polycarbonate
Weight		Approx. 75 g	Approx. 40 g	Approx. 75 g	Approx. 40 g
^1 Only the FS-T1 and FS-M1 can provide stability outputs. ^2 If more than one unit is used together, the ambient temperature varies with the conditions below. Mount the units on the DIN rail with mounting brackets and check that the output current is 20 mA or less. 3 to 10 Units: -10 to 50°C 14 to 122°F, 11 to 16 Units: -10 to 45°C 14 to 113°F ^3 When several units are connected, the ambient temperature requirement varies depending on the total number of units connected. When 3 to 10 units: -10 to +50 °C 14 to 122 °F When 11 to 16 units: -10 to +45 °C 14 to 113 °F When connecting several units, be sure to mount the units to a metallic DIN rail. Make sure that the output current does not exceed 20 mA. ^4 Power to the FS-T2/M2 is supplied through the FS-T1/M1/V1/V11/, PS-T1, LV-21A/11A.

Back to top

Model		FS-T1G
Image
Light source		Green LED
Response time		250 µs
Operation mode		LIGHT-ON/DARK-ON (switch-selectable)
Indicator lamp		Output indicator: Red LED, Stable operation indicator: Green LED, Calibration indicator: Orange LED
Timer function		ON-delay: 40 ms/OFF-delay: 40 ms/Timer OFF (switch-selectable)
External calibration input signal		Non-voltage input (contact, solid state)
Input
Control output		NPN open-collector 100 mA max. (24 VDC max.), Residual voltage: 1 V max.
Stability output		NPN open-collector: 50 mA max. (40 VDC max.), Residual voltage:1 V max
Protection circuit		Reversed polarity protection, over-current protection, surge absorber
Rating	Power voltage	12 to 24 VDC ±10 %, Ripple (P-P) 10 % or less
	Current consumption	35 mA or less
Environmental resistance	Ambient light	Incandescent lamp: 10,000 lux max., Sunlight: 20,000 lux max.
	Ambient temperature	-10 to +55 °C 14 to 131 °F (No freezing)^*1
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
	Shock resistance	500 m/s², 3 times in each of the X, Y, and Z directions
Case material		Polycarbonate
Weight		Approx. 75 g
^*1 When several units are connected, the ambient temperature requirement varies depending on the total number of units connected. When 3 to 10 units: -10 to +50 °C 14 to 122 °F When 11 to 16 units: -10 to +45 °C 14 to 113 °F When connecting several units, be sure to mount the units to a metallic DIN rail. Make sure that the output current does not exceed 20 mA.

Back to top

Model		FS-M1H
Image
Light source		Red LED
Sensitivity adjustment/Mode selection		8-turn trimmer (with indicator), FINE/TURBO (switch-selectable)
Response time		20 µs (FINE) /50 µs (TURBO)
Operation mode		LIGHT-ON/DARK-ON (switch-selectable)
Indicator lamp		Output: Red LED Stable operation: Green LED
Timer function		ON-delay: 40 ms/OFF-delay: 40 ms/Timer OFF (switch-selectable)
Control output		NPN open-collector 100 mA max. (24 VDC max.), Residual voltage: 1 V max.
Stability output		NPN open-collector: 50 mA max. (40 VDC max.), Residual voltage:1 V max.
Protection circuit		Reversed polarity protection, over-current protection, surge absorber
Rating	Power voltage	12 to 24 VDC ±10 %, Ripple (P-P) 10 % or less
	Current consumption	35 mA or less
Environmental resistance	Ambient light	Incandescent lamp: 10,000 lux max., Sunlight: 20,000 lux max.
	Ambient temperature	-10 to +55 °C 14 to 131 °F (No freezing)^*1
	Relative humidity	35 to 85 % RH (No condensation)
	Vibration resistance	10 to 55 Hz, Double amplitude 1.5 mm 0.06", 2 hours in each of the X, Y, and Z directions
	Shock resistance	500 m/s², 3 times in each of the X, Y, and Z directions
Case material		Polycarbonate
Weight		Approx. 75 g
^*1 When several units are connected, the ambient temperature requirement varies depending on the total number of units connected. When 3 to 10 units: -10 to +50 °C 14 to 122 °F When 11 to 16 units: -10 to +45 °C 14 to 113 °F When connecting several units, be sure to mount the units to a metallic DIN rail. Make sure that the output current does not exceed 20 mA.

Back to top

Specs Manual-Calibration Fiberoptic Sensor FS-V/T/M series