Controller, with Display Unit SI-F1000V

SI-F1000V - Controller, with Display Unit

*Please note that accessories depicted in the image are for illustrative purposes only and may not be included with the product.

Specifications

Model			SI-F1000V
Separate type			SI-F1000/SI-FD500
Type			Built-in main controller type
No. of connectable spectrum units			2
Display	Minimum display unit		0.001 µm
	Display range		±999.999 µm to ±9999.99 mm (7 settings selectable)
	Display cycle		10 times/sec
Terminal block	Laser remote interlock input		Non-voltage or voltage input ^1.^2
	TIMING1 input
	RESET1 input
	Auto-zero1 input
	Laser control input
	Analog voltage output		±10 V x 2 outputs, Output impedance: 100 Ω^*2
	Analog current output		4 to 20 mA x 2 outputs, Maximum load resistance: 350 Ω^*2
	Alarm output		NPN open-collector output (N.C.)^*2
	General comparator output		NPN open-collector output ^3^2
Expansion connector	TIMING2 input		Non-voltage or voltage input ^1.^2
	RESET input
	Auto-zero input
	Program switch input		Non-voltage input x 3 inputs^*2
	Alarm output		NPN open-collector output (N.C.)^*2
	Comparator/ binary output	Binary output	Measured value data output (21 bits) OUT selectable NPN open-collector output^*2
		Strobe output	NPN open-collector output ^3^2
		Binary selection output
		Binary selection input	Non-voltage or voltage input ^1.^2
RS-232C interface			Measured data output and control input/output (Maximum baud rate: 115200 bps, selectable)
USB interface			In conformity with USB Revision 2.0 HI-SPEED (USB 1.1 Full-SPEED compatible)
Ethernet interface			100BASE-TX/10BASE-T
Major functions			12 Out simultaneous measurementcalculation, average, filter, scaling measurement, measured value alarm, tolerance setting, auto-zero, data storage, light monitor, 8-program memory,interferometer mode, mask, connection of setting support software, etc.
Rating	Power voltage		24 VDC ±10 %, Ripple (P-P) 10 % or less
	Current consumption		One head connected: 0.6 A or less. Six heads connected: 1.5 A or less.
Environmental resistance	Ambient temperature		0 to +50 °C 32 to 122 °F^*4
	Relative humidity		35 to 85 % RH (No condensation)
	Vibration resistance		10 to 55 Hz, Double amplitude 0.5 mm 0.02", 2 hours in each of the X, Y, and Z directions
Weight			Approx. 600 g
^1 (NPN model) The rating of non-voltage input: 1 V or less ON voltage, 0.6 mA or less OFF current. (PNP model) The rating of voltage input: 10.2 V or more ON voltage (26.4 V max.) 0.6 mA or less OFFcurrent. ^2 • NPN open-collector output rating: 50 mA max. (40 V max.), Residual voltage: 0.5 V max. • Non-voltage input rating: ON voltage: 1 V max., OFF current: 0.6 mA max. • Part of the input/output circuit of the SI Series is internally common. Be careful that no potential difference is generated between the internally common terminals due to the potential difference between the cables/external devices. For details, refer to "Precautions on wiring". ^3 The rating of the NPN open-collector: 50 mA max. (40 V max.), residual voltage of 0.5 V max. The rating of the PNP open collector: 50 mA max. (30 V max.), residual voltage of 0.5 V max. ^4 When two or more expansion controllers are connected, the ambient temperature is 0 to +40 °C 32 to 104 °F.

Data Sheet (PDF) Other Models