Specs : Air Quality Multi-Sensor - MP-F series

Air Quality Multi-Sensor

Model		MP-FR10	MP-FR10R	MP-FR20	MP-FR20R	MP-FR80
Image
Type		Single model	Standard model	Single model	Standard model	Single model
Connection bore diameter		Rc3/8" (10 A)		Rc1/2" (15A)		Rc1" (25A)
Supported gases		Air and non-corrosive gases
Supported gas temperature		-5 to +50°C, 23 to 122°F
Operating pressure range		0.2 to 1 MPa, 2 to 10 bar, 29 to 145 psi ^*1
Pressure resistance		1.5 MPa, 15 bar, 217.5 psi
Flow rate	Detection principle	Heat based (mass flow rate)
	Rated flow range (normal)	2.0 to 1000.0 L/min 0.12 to 60.00 m³/h 4.24 to 2118.88 ft³/h 0.07 to 35.31 CFM		4 to 2000 L/min 0.2 to 120.0 m³/h 7.06 to 4237.76 ft³/h 0.1 to 70.6 CFM		12 to 8000 L/min 0.7 to 480.0 m³/h 24.72 to 16951.04 ft³/h 0.4 to 282.5 CFM
	Zero cut flow rate	2.0 L/min, 0.12 m³/h 4.24 ft³/h, 0.07 CFM		4 L/min, 0.2 m³/h 7.06 ft³/h, 0.1 CFM		12 L/min, 0.7 m³/h 24.72 ft³/h, 0.4 CFM
	Measurement accuracy	±(1.5% of RD + 0.5% of F.S.) ^2 ^3
	Repeatability	±1.0% of F.S. (with an averaging time of 1.0 s)
	Display resolution	0.1 L/min, 0.01 m³/h 0.35 ft³/h, 0.01 CFM		1 L/min, 0.1 m³/h 3.53 ft³/h, 0.1 CFM
	Response time	150 ms (63% response) ^*4
	Averaging time	OFF/100 ms/200 ms/500 ms/1.0 s/3.0 s/5.0 s/10 s/30 s (selectable)
Pressure (Digital value, gauge pressure)	Rated pressure range	0.000 to 1.000 MPa, 0.00 to 10.00bar, 0.0 to 145.0 psi
	Measurement accuracy	±2.0% of F.S.
	Repeatability	±0.2% of F.S. (with a response time of 50 ms)
	Display resolution	0.001 MPa, 0.01 bar, 0.1 psi
	Response time	Selectable from 10 ms, 50 ms, 100 ms, 500 ms, 1.0 s, and 5.0 s ^*4
Humidity (Dew point)	Rated relative humidity range/ dew point range	15 to 100%RH (no condensation)/Corresponds to the relative humidity range ^5 ^6
	Measurement accuracy	±4°C, ±7°F ^5 ^6
	Display resolution	5%RH/1°C, 1°F ^5 ^6
Temperature	Measurement accuracy	±2.0°C, ±3.6°F ^*7
	Display resolution	0.1°C, 0.1°F ^*7
Shut-off valve	Response time	1 s or less (closed → open)
	Leakage amount	50 mL/min 0.002 CFM (N) or less
Filter/regulator (Standard model only)	Pressure adjustment range	─	0.15 to 0.90 MPa	─	0.15 to 0.90 MPa	─
	Filtration degree		5 μm 0.196850 Mil		5 μm 0.196850 Mil
	Drainage cup capacity		60 cc		100 cc
Check valve		Available
Display		Color LCD, status indicator
Data accumulation	Accumulation period	Accumulated data: approx. 2 years/Instantaneous data: approx. 2 weeks
	Data reading	USB 2.0/Ethernet
I/O	Control output (Ch.1/2/3/4/5)	NPN/PNP setting switchable, open collector output 30 VDC or less, N.O./N.C. setting switchable, max. 100 mA/Ch., residual voltage: 2.5 V or less
	Analog output (Ch.1/2)	4 to 20 mA, load resistance: 260 Ω or less ^*4
	External input (Ch.2/3/6)	Short-circuit current: 1.5 mA or less, input time: 20 ms or more
Protection circuit		Power supply reverse connection protection, power supply surge protection, reverse connection protection for each I/O, surge protection for each I/O, overcurrent protection for each output
Power supply	Power voltage	24 VDC +25%/-20% (including ripple), Class 2 or LPS
	Power consumption	1.2 A (300 ms) when opening/closing valve, 100 mA at all other times ^*8 (standalone usage; excluding load current)
Communication interface		USB2.0
Network compatibility		When using only this unit: IO-Link (Specification v1.1/COM3) ^*9 When connecting MP-FEN1 : EtherNet/IP™, PROFINET, Modbus/TCP, MC protocol/SLMP
Environmental resistance	Enclosure rating	IP67 (IEC60529) ^*10
	Ambient temperature	−5°C to +50°C 23°F to 122°F (no freezing) ^*11
	Relative humidity	35%RH to 85%RH (no condensation)
	Vibration resistance	10 to 500 Hz; power spectral density: 0.204 G²/Hz; X, Y, and Z directions
	Shock resistance	300 m/s², XYZ axes, 10 times for each axis
Material		Sensor part : PET/PPS/PBT/POM/aluminum/SPHC Filter/regulator : Aluminum/POM/HDPE/NBR/Nylon ^*12
Weight		Approx. 550 g 19.40 oz	Approx. 1050 g 37.04 oz (excluding drainage cup)	Approx. 1020 g 35.98 oz	Approx. 1900 g 67.02 oz (excluding drainage cup)	Approx. 1920 g 67.73 oz
^1 An upstream side pressure of 0.2 MPa or less (a filter/regulator adjustment pressure of 0.2 MPa or less for the standard model) worsens the flow rate characteristic of the shut-off valve. ^2 This value is guaranteed by KEYENCE inspection facilities while testing with air. Errors will be introduced by factors such as the gas type, gas temperature, and ambient temperature. ^3 Value in an environment with a constant temperature of 25°C 77°F and compressed air evaluated as purity class 11 (ISO 8573-1 (2010)/JIS B 8392-1 (2012)).±(5.5% of RD + 0.5% of F.S.) when equivalent to purity class 34. ^4 15 ms is added to the analog output response time. ^5 Measurable when at least 2% of F.S. worth of gas is flowing. ^6 The prescribed accuracy may not be met or the unit may be damaged if the compressed air contains a large amount of oil mist, organic solvent, or other gas. (For details, see “Gas Being Measured” on page 4.) ^7 When the flow is 5% of F.S. or higher. Errors due to heat generated by the main unit occur when the flow is too small. ^8 When connecting MP-FEA1 and/or MP-FEN1, add each device’s current consumption (2.1 A or less including load current). ^9 Use an IO-Link master that can supply 1.2 A or more. (1.6 A or less when connecting an MP-FEA1 and an MP-FEN1.) IO-Link is a registered trademark or trademark of PROFIBUS Nutzerorganisation e.V. (PNO). ^10 When protection is provided to prevent dust and liquid from intruding through the exhaust port. The IP67 enclosure rating is lost when a USB connection is established. ^11 If this product is used with a power supply voltage of 26.4 V or more, the upper limit on the ambient temperature is 45°C 113°F. ^12 Nylon is only used on the MP-Fx20R.

Back to top

Air Quality Multi-Sensor

Model		MP-FG10	MP-FG10R	MP-FG20	MP-FG20R	MP-FG80
Image
Type		Single model	Standard model	Single model	Standard model	Single model
Connection bore diameter		G3/8" (10 A)		G1/2" (15A)		G1" (25A)
Supported gases		Air and non-corrosive gases
Supported gas temperature		-5 to +50°C, 23 to 122°F
Operating pressure range		0.2 to 1 MPa, 2 to 10 bar, 29 to 145 psi ^*1
Pressure resistance		1.5 MPa, 15 bar, 217.5 psi
Flow rate	Detection principle	Heat based (mass flow rate)
	Rated flow range (normal)	2.0 to 1000.0 L/min 0.12 to 60.00 m³/h 4.24 to 2118.88 ft³/h 0.07 to 35.31 CFM		4 to 2000 L/min 0.2 to 120.0 m³/h 7.06 to 4237.76 ft³/h 0.1 to 70.6 CFM		12 to 8000 L/min 0.7 to 480.0 m³/h 24.72 to 16951.04 ft³/h 0.4 to 282.5 CFM
	Zero cut flow rate	2.0 L/min, 0.12 m³/h 4.24 ft³/h, 0.07 CFM		4 L/min, 0.2 m³/h 7.06 ft³/h, 0.1 CFM		12 L/min, 0.7 m³/h 24.72 ft³/h, 0.4 CFM
	Measurement accuracy	±(1.5% of RD + 0.5% of F.S.) ^2 ^3
	Repeatability	±1.0% of F.S. (with an averaging time of 1.0 s)
	Display resolution	0.1 L/min, 0.01 m³/h 0.35 ft³/h, 0.01 CFM		1 L/min, 0.1 m³/h 3.53 ft³/h, 0.1 CFM
	Response time	150 ms (63% response) ^*4
	Averaging time	OFF/100 ms/200 ms/500 ms/1.0 s/3.0 s/5.0 s/10 s/30 s (selectable)
Pressure (Digital value, gauge pressure)	Rated pressure range	0.000 to 1.000 MPa, 0.00 to 10.00bar, 0.0 to 145.0 psi
	Measurement accuracy	±2.0% of F.S.
	Repeatability	±0.2% of F.S. (with a response time of 50 ms)
	Display resolution	0.001 MPa, 0.01 bar, 0.1 psi
	Response time	Selectable from 10 ms, 50 ms, 100 ms, 500 ms, 1.0 s, and 5.0 s ^*4
Humidity (Dew point)	Rated relative humidity range/ dew point range	15 to 100%RH (no condensation)/Corresponds to the relative humidity range ^5 ^6
	Measurement accuracy	±4°C, ±7°F ^5 ^6
	Display resolution	5%RH/1°C, 1°F ^5 ^6
Temperature	Measurement accuracy	±2.0°C, ±3.6°F ^*7
	Display resolution	0.1°C, 0.1°F ^*7
Shut-off valve	Response time	1 s or less (closed → open)
	Leakage amount	50 mL/min 0.002 CFM (N) or less
Filter/regulator (Standard model only)	Pressure adjustment range	─	0.15 to 0.90 MPa	─	0.15 to 0.90 MPa	─
	Filtration degree		5 μm 0.196850 Mil		5 μm 0.196850 Mil
	Drainage cup capacity		60 cc		100 cc
Check valve		Available
Display		Color LCD, status indicator
Data accumulation	Accumulation period	Accumulated data: approx. 2 years/Instantaneous data: approx. 2 weeks
	Data reading	USB 2.0/Ethernet
I/O	Control output (Ch.1/2/3/4/5)	NPN/PNP setting switchable, open collector output 30 VDC or less, N.O./N.C. setting switchable, max. 100 mA/Ch., residual voltage: 2.5 V or less
	Analog output (Ch.1/2)	4 to 20 mA, load resistance: 260 Ω or less ^*4
	External input (Ch.2/3/6)	Short-circuit current: 1.5 mA or less, input time: 20 ms or more
Protection circuit		Power supply reverse connection protection, power supply surge protection, reverse connection protection for each I/O, surge protection for each I/O, overcurrent protection for each output
Power supply	Power voltage	24 VDC +25%/-20% (including ripple), Class 2 or LPS
	Power consumption	1.2 A (300 ms) when opening/closing valve, 100 mA at all other times ^*8 (standalone usage; excluding load current)
Communication interface		USB2.0
Network compatibility		When using only this unit: IO-Link (Specification v1.1/COM3) ^*9 When connecting MP-FEN1 : EtherNet/IP™, PROFINET, Modbus/TCP, MC protocol/SLMP
Environmental resistance	Enclosure rating	IP67 (IEC60529) ^*10
	Ambient temperature	−5°C to +50°C 23°F to 122°F (no freezing) ^*11
	Relative humidity	35%RH to 85%RH (no condensation)
	Vibration resistance	10 to 500 Hz; power spectral density: 0.204 G²/Hz; X, Y, and Z directions
	Shock resistance	300 m/s², XYZ axes, 10 times for each axis
Material		Sensor part : PET/PPS/PBT/POM/aluminum/SPHC Filter/regulator : Aluminum/POM/HDPE/NBR/Nylon ^*12
Weight		Approx. 550 g 19.40 oz	Approx. 1050 g 37.04 oz (excluding drainage cup)	Approx. 1020 g 35.98 oz	Approx. 1900 g 67.02 oz (excluding drainage cup)	Approx. 1920 g 67.73 oz
^1 An upstream side pressure of 0.2 MPa or less (a filter/regulator adjustment pressure of 0.2 MPa or less for the standard model) worsens the flow rate characteristic of the shut-off valve. ^2 This value is guaranteed by KEYENCE inspection facilities while testing with air. Errors will be introduced by factors such as the gas type, gas temperature, and ambient temperature. ^3 Value in an environment with a constant temperature of 25°C 77°F and compressed air evaluated as purity class 11 (ISO 8573-1 (2010)/JIS B 8392-1 (2012)).±(5.5% of RD + 0.5% of F.S.) when equivalent to purity class 34. ^4 15 ms is added to the analog output response time. ^5 Measurable when at least 2% of F.S. worth of gas is flowing. ^6 The prescribed accuracy may not be met or the unit may be damaged if the compressed air contains a large amount of oil mist, organic solvent, or other gas. (For details, see “Gas Being Measured” on page 4.) ^7 When the flow is 5% of F.S. or higher. Errors due to heat generated by the main unit occur when the flow is too small. ^8 When connecting MP-FEA1 and/or MP-FEN1, add each device’s current consumption (2.1 A or less including load current). ^9 Use an IO-Link master that can supply 1.2 A or more. (1.6 A or less when connecting an MP-FEA1 and an MP-FEN1.) IO-Link is a registered trademark or trademark of PROFIBUS Nutzerorganisation e.V. (PNO). ^10 When protection is provided to prevent dust and liquid from intruding through the exhaust port. The IP67 enclosure rating is lost when a USB connection is established. ^11 If this product is used with a power supply voltage of 26.4 V or more, the upper limit on the ambient temperature is 45°C 113°F. ^12 Nylon is only used on the MP-Fx20R.

Back to top

Air Quality Multi-Sensor

Model		MP-FN10	MP-FN10R	MP-FN20	MP-FN20R	MP-FN80
Image
Type		Single model	Standard model	Single model	Standard model	Single model
Connection bore diameter		NPT3/8" (10 A)		NPT1/2" (15A)		NPT1" (25A)
Supported gases		Air and non-corrosive gases
Supported gas temperature		-5 to +50°C, 23 to 122°F
Operating pressure range		0.2 to 1 MPa, 2 to 10 bar, 29 to 145 psi ^*1
Pressure resistance		1.5 MPa, 15 bar, 217.5 psi
Flow rate	Detection principle	Heat based (mass flow rate)
	Rated flow range (normal)	2.0 to 1000.0 L/min 0.12 to 60.00 m³/h 4.24 to 2118.88 ft³/h 0.07 to 35.31 CFM		4 to 2000 L/min 0.2 to 120.0 m³/h 7.06 to 4237.76 ft³/h 0.1 to 70.6 CFM		12 to 8000 L/min 0.7 to 480.0 m³/h 24.72 to 16951.04 ft³/h 0.4 to 282.5 CFM
	Zero cut flow rate	2.0 L/min, 0.12 m³/h 4.24 ft³/h, 0.07 CFM		4 L/min, 0.2 m³/h 7.06 ft³/h, 0.1 CFM		12 L/min, 0.7 m³/h 24.72 ft³/h, 0.4 CFM
	Measurement accuracy	±(1.5% of RD + 0.5% of F.S.) ^2 ^3
	Repeatability	±1.0% of F.S. (with an averaging time of 1.0 s)
	Display resolution	0.1 L/min, 0.01 m³/h 0.35 ft³/h, 0.01 CFM		1 L/min, 0.1 m³/h 3.53 ft³/h, 0.1 CFM
	Response time	150 ms (63% response) ^*4
	Averaging time	OFF/100 ms/200 ms/500 ms/1.0 s/3.0 s/5.0 s/10 s/30 s (selectable)
Pressure (Digital value, gauge pressure)	Rated pressure range	0.000 to 1.000 MPa, 0.00 to 10.00bar, 0.0 to 145.0 psi
	Measurement accuracy	±2.0% of F.S.
	Repeatability	±0.2% of F.S. (with a response time of 50 ms)
	Display resolution	0.001 MPa, 0.01 bar, 0.1 psi
	Response time	Selectable from 10 ms, 50 ms, 100 ms, 500 ms, 1.0 s, and 5.0 s ^*4
Humidity (Dew point)	Rated relative humidity range/ dew point range	15 to 100%RH (no condensation)/Corresponds to the relative humidity range ^5 ^6
	Measurement accuracy	±4°C, ±7°F ^5 ^6
	Display resolution	5%RH/1°C, 1°F ^5 ^6
Temperature	Measurement accuracy	±2.0°C, ±3.6°F ^*7
	Display resolution	0.1°C, 0.1°F ^*7
Shut-off valve	Response time	1 s or less (closed → open)
	Leakage amount	50 mL/min 0.002 CFM (N) or less
Filter/regulator (Standard model only)	Pressure adjustment range	─	0.15 to 0.90 MPa	─	0.15 to 0.90 MPa	─
	Filtration degree		5 μm 0.196850 Mil		5 μm 0.196850 Mil
	Drainage cup capacity		60 cc		100 cc
Check valve		Available
Display		Color LCD, status indicator
Data accumulation	Accumulation period	Accumulated data: approx. 2 years/Instantaneous data: approx. 2 weeks
	Data reading	USB 2.0/Ethernet
I/O	Control output (Ch.1/2/3/4/5)	NPN/PNP setting switchable, open collector output 30 VDC or less, N.O./N.C. setting switchable, max. 100 mA/Ch., residual voltage: 2.5 V or less
	Analog output (Ch.1/2)	4 to 20 mA, load resistance: 260 Ω or less ^*4
	External input (Ch.2/3/6)	Short-circuit current: 1.5 mA or less, input time: 20 ms or more
Protection circuit		Power supply reverse connection protection, power supply surge protection, reverse connection protection for each I/O, surge protection for each I/O, overcurrent protection for each output
Power supply	Power voltage	24 VDC +25%/-20% (including ripple), Class 2 or LPS
	Power consumption	1.2 A (300 ms) when opening/closing valve, 100 mA at all other times ^*8 (standalone usage; excluding load current)
Communication interface		USB2.0
Network compatibility		When using only this unit: IO-Link (Specification v1.1/COM3) ^*9 When connecting MP-FEN1 : EtherNet/IP™, PROFINET, Modbus/TCP, MC protocol/SLMP
Environmental resistance	Enclosure rating	IP67 (IEC60529) ^*10
	Ambient temperature	−5°C to +50°C 23°F to 122°F (no freezing) ^*11
	Relative humidity	35%RH to 85%RH (no condensation)
	Vibration resistance	10 to 500 Hz; power spectral density: 0.204 G²/Hz; X, Y, and Z directions
	Shock resistance	300 m/s², XYZ axes, 10 times for each axis
Material		Sensor part : PET/PPS/PBT/POM/aluminum/SPHC Filter/regulator : Aluminum/POM/HDPE/NBR/Nylon ^*12
Weight		Approx. 550 g 19.40 oz	Approx. 1050 g 37.04 oz (excluding drainage cup)	Approx. 1020 g 35.98 oz	Approx. 1900 g 67.02 oz (excluding drainage cup)	Approx. 1920 g 67.73 oz
^1 An upstream side pressure of 0.2 MPa or less (a filter/regulator adjustment pressure of 0.2 MPa or less for the standard model) worsens the flow rate characteristic of the shut-off valve. ^2 This value is guaranteed by KEYENCE inspection facilities while testing with air. Errors will be introduced by factors such as the gas type, gas temperature, and ambient temperature. ^3 Value in an environment with a constant temperature of 25°C 77°F and compressed air evaluated as purity class 11 (ISO 8573-1 (2010)/JIS B 8392-1 (2012)).±(5.5% of RD + 0.5% of F.S.) when equivalent to purity class 34. ^4 15 ms is added to the analog output response time. ^5 Measurable when at least 2% of F.S. worth of gas is flowing. ^6 The prescribed accuracy may not be met or the unit may be damaged if the compressed air contains a large amount of oil mist, organic solvent, or other gas. (For details, see “Gas Being Measured” on page 4.) ^7 When the flow is 5% of F.S. or higher. Errors due to heat generated by the main unit occur when the flow is too small. ^8 When connecting MP-FEA1 and/or MP-FEN1, add each device’s current consumption (2.1 A or less including load current). ^9 Use an IO-Link master that can supply 1.2 A or more. (1.6 A or less when connecting an MP-FEA1 and an MP-FEN1.) IO-Link is a registered trademark or trademark of PROFIBUS Nutzerorganisation e.V. (PNO). ^10 When protection is provided to prevent dust and liquid from intruding through the exhaust port. The IP67 enclosure rating is lost when a USB connection is established. ^11 If this product is used with a power supply voltage of 26.4 V or more, the upper limit on the ambient temperature is 45°C 113°F. ^12 Nylon is only used on the MP-Fx20R.

Back to top

Energy Monitor

Model			MP-FEA1
Image
Measurement specifications	Electrical service type		1-phase 2-wire, 1-phase 3-wire, 3-phase 3-wire, 3-phase 4-wire (switchable)
	Number of measurement circuits		1 (up to 2 circuits with the 1-phase 2-wire setting ^*1)
Input specifications	Primary-side rated current, In		When using specialized CT MP-FEC100: 100 A Or, general CT (secondary-side rated input current 1 A) ^2 When using specialized CT MP-FEC250: 250 A Or, general CT (secondary-side rated input current 1 A) ^2 When using specialized CT MP-FEC600: 600 A Or, general CT (secondary-side rated input current 1 A) ^*2 When using specialized CT MP-FEC50M: 50 A When using specialized CT MP-FEC100M: 100 A
	Over current withstand capability		1.2 times the primary-side rated current (can be applied consecutively), 10 times the primary-side rated current (for 1 second or less)
	Rated input voltage (direct input)	1-phase 2-wire	・MP-FEC100/MP-FEC250/MP-FEC600, or general CT in use: 100 to 277 VAC (L-N) ・MP-FEC50M/MP-FEC100M in use: 100 to 240 VAC (L-N)
		1-phase 3-wire	・MP-FEC100/MP-FEC250/MP-FEC600, or general CT in use: 100 to 240 VAC (L-N), 200 to 480 VAC (L-L) ・MP-FEC50M/MP-FEC100M in use: 100 to 240 VAC (L-N), 200 to 480 VAC (L-L)
		3-phase 3-wire	・MP-FEC100/MP-FEC250/MP-FEC600, or general CT in use: 173 to 480 VAC (L-L) ・MP-FEC50M/MP-FEC100M in use: 173 to 240 VAC (L-L)
		3-phase 4-wire	・MP-FEC100/MP-FEC250/MP-FEC600, or general CT in use: 100 to 277 VAC (L-N), 173 to 480 VAC (L-L) ・MP-FEC50M/MP-FEC100M in use: 100 to 240 VAC (L-N), 173 to 415 VAC (L-L)
	Maximum permissible voltage to earth		・MP-FEC100/MP-FEC250/MP-FEC600, or general CT in use: 480 VAC to earth ・MP-FEC50M/MP-FEC100M in use: 240 VAC to earth
	Input voltage fluctuation range		−15% to +15% of the rated input voltage
	Rated input frequency		50/60 Hz
Displayable range/ Display resolution (Main Unit)	Voltage		Display resolution 0.1 [V]
	Current		Display resolution 0.001 [A]
	Active power/reactive power/apparent power		-8942.400 to +8942.400 [kW/kvar/kVA], display resolution 0.001 [kW/kvar/kVA]
	Active energy/reactive energy/apparent energy		0.000 to 999999.999 [kWh/kvarh/kVAh], display resolution 0.001 [kWh/kvarh/kVAh]
	Power factor (PF)		-1.00 to 1.00, display resolution 0.01
	Frequency		0.0 to 90.0 [Hz], display resolution 0.1 [Hz]
Measurement accuracy	Voltage		±0.5% of RD (within rated input voltage) ^*3
	Current		・MP-FEC100/MP-FEC250/MP-FEC600, or general CT in use: ±0.5% of RD (5% ≤ In ≤ 120%), ±1.0% of RD (1% ≤ In < 5%) ^2 ^3 ・MP-FEC50M/MP-FEC100M in use: ±0.5% of F.S. ^*3
	Active energy		・MP-FEC100/MP-FEC250/MP-FEC600, or general CT in use: Compliant with IEC 62053-22 §7.9 table 3 class 0.5 ^2 ^3 Power factor 1: ±0.5% of RD (5% ≤ In ≤ 120%), ±1.0% of RD (1% ≤ In < 5%) Power factor 0.5 inductive: ±0.6% of RD (10% ≤ In ≤ 120%), ±1.0% of RD (2% ≤ In < 10%) Power factor 0.8 capacitive: ±0.6% of RD (10% ≤ In ≤ 120%), ±1.0% of RD (2% ≤ In < 10%) ・MP-FEC50M/MP-FEC100M in use: ±1.0% of RD (1% ≤ In ≤ 120%) ^*3
	Reactive energy		・MP-FEC100/MP-FEC250/MP-FEC600, or general CT in use: Compliant with IEC 62053-23 §7.9 table 3 class 2 ^2 ^3 Reactive power factor 1: ±2.0% of RD (5% ≤ In ≤ 120%), ±2.5% of RD (1% ≤ In < 5%) Reactive power factor 0.5 inductive or capacitive: ±2.0% of RD (10% ≤ In ≤ 120%), ±2.5% of RD (5% ≤ In < 10%) Reactive power factor 0.25 inductive or capacitive: ±2.5% of RD (10% ≤ In ≤ 120%) ・MP-FEC50M/MP-FEC100M in use: ±2.0% of RD (5% ≤ In ≤ 120%) ^*3
	Apparent energy		・MP-FEC100/MP-FEC250/MP-FEC600, or general CT in use: ±0.5% of RD (5% ≤ In ≤ 120%), ±1.0% of RD (1% ≤ In < 5%) ^2 ^3 ・MP-FEC50M/MP-FEC100M in use: ±1.0% of RD (5% ≤ In ≤ 120%) ^3 ^4
	Effect of ambient temperature		±0.03%/K ^3 ^5
	Effect of harmonics		±0.5% of RD ^3 ^6
	Power factor (PF)		±0.01 ^*3
	Power		±0.1 [Hz] ^*3
Current consumption			36 mA
Withstand voltage			Across all terminals and housing: 2500 VAC for 1 minute Across voltage measurement terminal and communication terminal: 2500 VAC for 1 minute Across CT input terminal and communication terminal (When using a specialized CT): 2500 V for 1 minute
Insulation resistance			Across all terminals and housing: 20 MΩ min. (500 VDC) Across voltage measurement terminal and CT input terminal and across communication terminal: 20 MΩ min. (500 VDC)
Environmental resistance	Ambient temperature		-5 to +55°C 23 to 131°F (no freezing)
	Relative humidity		35%RH to 85%RH (no condensation)
	Measurement category		II
	Altitude		2500 m or less
	Pollution degree		2
	Mounting method		DIN rail mounting
	Vibration resistance		10 to 500 Hz, power spectral concentration: 0.033G²/Hz, XYZ axes
	Shock resistance		150 m/s², 2 times each for X, Y, and Z axes
Material			Polycarbonate
Weight			Approx. 110 g 3.88 oz
^1 When measuring two circuits, use a power supply with the same voltage and phase for the two circuits. Also, use CTs of the same model. ^2 Primary-side rated current: 1 to 2000 A, secondary-side rated input current: 1 A, nominal cross-sectional area: 0.2 mm² to 1.5 mm² 0.0003 in² to 0.0023 in². However, when a general CT is used, the requirements of the EU Directive(s) and CSA Certification are not met. ^3 This value assumes an ambient temperature of 23°C 73.4°F and the rated frequency. The accuracy of the CT is not included. Also, the display may be offset by an amount equal to the display resolution. ^4 Displays a guideline value when the total apparent energy is displayed with multiple energy monitors used. ^5 Excluding the time for warm up after starting communication and the temperature fluctuations attributable to measurement current fluctuations. ^6 Error when the second, third, fifth, seventh, ninth, eleventh, and thirteenth harmonics are superimposed on the base wave with current content of 30% and voltage content of 5%.

Back to top

CT (external current sensor)

Model		MP-FEC50M	MP-FEC100M	MP-FEC100	MP-FEC250	MP-FEC600
Image
Primary-side rated current (In)		50 A	100 A		250 A	600 A
Over current withstand capability		1.2 times the primary-side rated current (can be applied consecutively)
Max. connectable is correct wire diameter		ø10 0.39"	ø16 0.63"	ø24 0.94"		ø35 1.38"
Mounting method		Clamp method (split core)
Specific error on current load		±0.5% of RD (20%≤In≤100%)		±2.0% of RD (20%≤In≤100%)	±1.0% of RD (20%≤In≤100%)
Phase difference on current load		±90’ (20% In) ±90’ (100% In)		±240’ (20% In) ±180’ (100% In)	±60’ (20% In) ±60’ (100% In)
Withstand voltage		2300 VAC for 1 minute (across core and output lead)
Insulation resistance		500 VDC/100 MΩ or more (across core and output lead)
Protective element		Internal clamp element
Environmental resistance	Ambient temperature	−10°C to +55°C 14 to 131°F (no freezing)
	Relative humidity	35%RH to 85%RH (no condensation)
Material		Nylon
Weight		Approx. 140 g 4.94 oz (including cable)	Approx. 170 g 6.00 oz (including cable)	Approx. 300 g 10.58 oz (including cable)	Approx. 315 g 11.11 oz (including cable)	Approx. 450 g 15.87 oz (including cable)

Back to top

Ethernet Module

Model		MP-FEN1
Image
Ethernet specifications	Compliant standard	IEEE802.3u (100BASE-TX)
	Transmission rate	100 Mbps (100BASE-TX)
	Transmission media	Category 5 or higher STP (shielded twisted pair)
	Connector type	M12, 4-pin, female, D-code
	Maximum cable length	100 m 328.1' (between nodes)
	Supported networks	EtherNet/IP™, PROFINET, Modbus/TCP, MC protocol/SLMP
Number of connectible models/units		MP-F main unit: 1 MP-FEA1: up to 10 FD-R: 1
EtherNet/IP™	Supported functions	Cyclic communication (Implicit messaging) Message communication (Explicit messaging)
	Number of connections	16
	Supported connections	Input Only, Exclusive Owner
	RPI (communication cycle)	4 to 10,000 ms
PROFINET	Compatible network	PROFINET IO communication
	Supported functions	Cyclic communication (data I/O communication) Acyclic communication (record data communication)
	Conformance class	Compliant with Conformance Class B
	Conformance test version	Compliant with ver. 2.42
	Applicable protocols	LLDP, SNMP, DCP
	Net load	Class 2
	Cyclic update time	4 to 2048 ms
MODBUS/TCP	Communication method	TCP/IP
	Compatible configuration	Server
	Maximum number of simultaneous client connections	4
MC protocol/ SLMP	Communication method	TCP/IP, UDP/IP
	Maximum number of connections	4
	Compatible frames	QnA-compatible 3E frame, 4E frame
	Data format	Binary/ASCII
Power supply specifications	Connector type	M12, 4 pins, A-code, cable length: 50 cm 19.69"
	Power supply voltage	24 VDC +25%/-20% (including ripple), Class 2 or LPS
	Current consumption	40 mA ^*1
Environmental resistance	Enclosure rating	IP67 (IEC60529)
	Ambient temperature	−20 to 60°C -4 to +140°F
	Relative humidity	35%RH to 85%RH (no condensation)
	Vibration resistance	10 to 500 Hz; power spectral density: 0.816 G²/Hz; X, Y, and Z directions
	Shock resistance	100 m/s², XYZ axes, 1000 times for each axis
Material		Case: PBT/PAR Connector: Nickel-plated brass
Weight		Approx. 150 g 5.29 oz
^*1 When connecting to the FD-R Series: 190 mA max.

Back to top

Specs Air Quality Multi-Sensor MP-F series

Air Quality Multi-Sensor

Air Quality Multi-Sensor

Air Quality Multi-Sensor

Energy Monitor

CT (external current sensor)

Ethernet Module